알마즌닷컴

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Window Sash Repairs

Check the windows sashes regularly for damage, mildew, and mold. By catching problems before they become serious you will save money on future repairs.

The sash is an interior framing that moves vertically up or down in windows that open. This article will demonstrate how to do a variety of simple repairs to the sash.

Weather Stripping

Wood window sashes provide a classic aesthetic to your home and, when properly maintained, they will last for years. However, they can become damaged or deteriorate in time due to exposure to the elements and wear and 257634.Xyz tear. Fortunately, sash repair specialists can bring your windows back to their original condition and keep them looking fantastic for a longer period of time than replacement windows.

The first step in repair sash windows is to address weather stripping, which is found on both the sash and frame. It can cause drafts if it's worn out or loose. To fix it, start by determining your window's brand and Www.257634.Xyz the date of manufacture for the glass (etched in the corner of the glass or on the aluminum spacer between panes). Then, remove the sash and mark its height and width so that you can locate replacement weather stripping to match.

Then, remove the sash from its holder, and place it on flat surfaces to allow you to access all four sides. If the sash is double-hung, you must remove the weights using their ropes that should be buried within the jamb lining. After removing the sash using the utility knife, take off the old weather stripping by hand or with the putty blade.

When the sash is clean, you can replace the parting stops. They are long pieces of wood that divide the two sashes. Pam likes to replace these with standard 1/2-inch-by - 3/4-inch window trim from the lumberyard, but you can also replace them with scrap wood.

After removing the stopper and trimming it to length, apply a thin coat of glazing compound on the bottom of the sash. Smooth the compound with your putty knife and www.257634.xyz let it dry for at least a few days. When the putty is fully cure it is possible to apply an acrylic latex topcoat. This coating will protect the putty and give your sash a fresh look.

Sash Hardware

The hardware that supports window sashes is prone to wearing out from time and usage and the result could be a window or door 257634.xyz (257634.Xyz) that isn't able to open or close easily. The good news is that fixing and replacing this hardware is usually quite simple and inexpensive. If a sash isn't easy to operate, try spraying some grease into the jamb channel and then slide it open to see if this solves the issue. If not, the issue is likely with the sash balance, and you'll need to remove the sash to access the hardware.

Window sashes should open and close without much effort. However, this may be difficult if weights are worn out or the sash-to-rail connecting rail isn't coated. This issue could be caused by various reasons such as a lack of maintenance and an unmatched weight rating.

If the hinge arms on a window begin to sag this could cause the sash to drag and eventually hit against the frame in the opposite corner (Photo 1). To fix this problem, first ensure that the sash is squarely inserted into the frame's opening and then take it out of the window. If the sash is screwed onto the hinge arm, remove the hinge and replace it. (Photo 2). Install the new sash next (Photo 3).

Due to hinges that are sagging, and a general deficiency in energy efficiency, older windows, especially those in older homes, may be difficult to open and close. Sometimes, a few simple fixes can make these windows operate smoothly again and save homeowners money on energy costs.

In order to make these repairs to sash it is essential to have all the tools needed before you begin. Mark the location of the hinge channel on the frame (Photo 1) with pencil. This will assist you in getting the channel back on position correctly after you've completed. Take the sash off and then remove all hardware, including the beads for parting cords, chains, and cords that help to hold the sash. Soften any putty that has been hardened with the help of a heat gun set at medium and fitted with a shield to block the nozzle. Remove the old sash and place it in a bag that is labeled.

Sash Weights

Sash weights can be replaced to improve the performance of your window sash, and also reduce the cost of energy. Sash weights are heavy lead or iron cylinders enclosed in a hidden cavity and connected to the movable sash by rope. These weights provide counterbalance which allows the window to be closed and opened without using mechanical or electrical devices. When they fail, sashweights are usually neglected or not used by homeowners.

It is difficult to recover an sash-weight which has fallen from the cavity, so you'll want to find one that fits correctly. You will also require a fresh piece of string, a length of sashcord and a few sashpulleys to secure the new weights to the cord.

Older wood windows are joined by mortise and tenon joints. Pin punch and hammer can be used to take out the wood pegs holding the parts together. Most of them have large diameters on one side and a smaller diameter on the other, which is why it is essential to remove the smaller-diameter sides first. Sashes made later in the century used glue instead of pegs and can be separated by cutting through the glue line using the help of a knife, and then tapping the mortised part loose using a mallet.

After the sash is removed, you can remove the sash stop and access the weight pocket. Usually, this is done through an opening at the bottom of each jamb. This hole is then covered by an access panel of wood that can be cut off to allow you to observe the inner workings of the frame.

After the sash has been stopped and the access panel removed, you'll be able to remove the weight of the old sash and replace it with the new. Be sure to weigh the sash prior to you do this, since the weights that were previously used may be different sizes than the one you need. Once the new weight has been installed, thread a string through the sash pulling mechanism. Then, you can attach the string to your boxed frame. Leave a few inches of space at the top of the string for future adjustments.

Sash Cords

Most old double-hung windows have a cord or chain attached to the weights that supports and keeps the sashes in balance within the jamb. As time passes, these cords may break, making it difficult to raise the window. A new sash cord will give you the ability to move the sash up and down and will keep it in its place when opened.

To replace sash cords, the first step is to remove the access panels from the jambs. These are usually nailed or screwed in and must be removed or repositioned. It is possible to remove them using an axe or hammer, however, it is best to lay out dust sheets before starting any work.

After the access panel has been removed, you can begin working on the sash. Use a flat bar or chisel to pry the tiny parting beads out of their grooves. They are typically wedged into or nailed in, but they can be prised free and it's worth your time here. If the sash remains in place, break the mortise-and tenon joints with a hammer or screwdriver and then remove each wood peg. You should now be able to move the sash around freely, although it will probably need some oil if it feels stiff.

Determine the length of sash cord/chain needed to reach the sash slot at the bottom of the pulley on the top of the jamb. Cut the chain or cord and then attach it as described in the previous step. You can use either a hammer, nails or screws. However, nails are less likely than screws to cause damage.

If you don't have an item that replaces the counterbalance system that was in place before, it is recommended to keep the original weights for balancing in place. They are not expensive and simple to install if you purchase them at architectural salvage stores. Depending on the size of your window, one or two sashweights might be required to keep it in an open position.