알마즌닷컴

Patio Door Lock Repairs

Over time, patio doors experience wear and tear that can cause lock malfunctions. There are a few basic steps you can take to restore the security of your uPVC door.

These simple fixes will ensure your home is secure no matter if you adjust the lock or clean the locking mechanism.

Clean the Lock

Patio doors are great for letting the outdoors in while keeping out the elements. However they could pose risky for security when the lock isn't functioning correctly. Over time, wear, tear, hot and cold weather dirt and debris can cause your patio door lock to become difficult to operate. With a little attention you can ensure that your patio door glass repair near me door's lock is always working correctly.

It's important to first clean the patio door lock and all moving parts. This will help flush out any accumulated grime and coatings that could be preventing the lock from functioning as it should. Begin by wiping down all the moving parts on the lock for your patio door with an aqueous cloth. Then apply a scouring pad or a damp, rough cloth to scrub the dirt-infested parts of the door frame and frame. Then, wipe the lock down with a dry towel to remove any remaining moisture. Let it air dry before you use it.

If your patio door uses pin-tumbler locks You can apply powdered Graphite to the key. You can also apply a Teflon lubricant like WD-40 Multi-Use Product. This type of lubricant can be applied quickly and will not disintegrate over time. If you are unable to find an appropriate lubricant you can try using a pencil with a thick tip. Put the pencil in the lock, then shake it to distribute the graphite.

Sliding patio door tracks also require regular maintenance to keep them free of dust, dirt, and debris. These tracks are especially susceptible to snow and ice which can cause them to jam or bind which makes it difficult for your patio doors to open and close.

Clean the track rails and rollers of sliding patio doors by removing any damaged or dirty weather stripping. Clean it, and then replace it. Patio door rollers can also be cleaned and sprayed with an oil that is non-stick.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, operate using 3 to 4, or occasionally 5 points locking mechanisms. They include the lock cylinder and handle which is operated by a key. They require maintenance and the lubrication of moving parts. This can be done with a thin oil but not WD40. It is recommended to do it every year, at a minimum.

If sagging hinges don't cause the problem it could be because the door is misaligned. It may be rubbing or catching against the strike plate's opening in the frame. The solution is to take off the strike plate and then use an abrasive chisel to increase the size of the mortise that it rests in. This allows the latch to sit perfectly in the hole, and also prevents rubbing or catching on the frame.

Take a measurement of the width of the cylinder with the help of a piece of wood or a book that can be inserted into the gap above the adjustment screw. The outer dimension is the distance from the outside of the door to the center of the cylinder, while the inner measurement runs from the center of the adjustment screw to the end of the cylinder.

Check the lock's width

If your patio door latch is difficult to turn, even after oiling and cleaning it's possible that it is not aligned with the strike plate. Check to see if the door is balanced and whether the hinge screws are secure, but in many cases it is possible to move the strike plate upwards or downwards could fix the problem.

Oftentimes, the problem occurs when the strike of the lock is too small for the latch to properly engage. In this situation, you'll need to enlarge the hole with a chisel or hammer and then test the latch to make sure that it contacts the strike plate in a smooth manner without rubbing against or getting caught on the door's frame jamb.

Before purchasing a new lock, first determine the mortise type of lock you currently have. You can do this by looking at the faceplate on the lock and determining if it is square or round. Look at each screw hole on the current lock and note their dimensions. This will enable you to locate the replacement lock that has exactly the same width and will fit in the hole that you already have.

You'll need to locate the mortise lock and examine it for scratches, bends or other damage that requires to be repaired. A badly damaged or bent latch is more likely break than one that's not utilized often, so make sure to replace the lock with a brand new secure and safe version in the event you notice any signs of wear or damage.

Once you've decided on the kind of lock replacement you require It's time to begin the actual repair. The old handle and spindle must be removed from the doorway to the patio. Install the new handle. Start by installing the inside handle. Align it with the spindle and then secure it in position using two bolts or screws. Install the exterior handle after the interior handle. After you've completed these steps, you can test the new handles to make sure they are able to open and close with ease and that the latch is catching correctly with the strike plate.

Make sure you check the Strike of the door.

The door latch and strike plate are the two parts of the lock that work together to ensure that the latch locks the door. An incorrectly aligned strike plate and door latch will result in the latch not being able to latch the door properly. Fortunately, the issue is often easy to fix.

Check the holes for receiving of the strike plate to ensure they are clear of obstructions, such as dirt or plastic plugs. Loosen the keeper screws holding the strike plate. This will allow it to move vertically, but not separate it from the frame. Then, you can adjust the strike plate until its receiving holes align with the latch hooks on the door latch. Once the strike plate is adjusted tighten the screws, and test the door to determine whether it shuts easily with the new adjustment.

Door strike plates can be difficult to access for homeowners who have sliding patio doors, however they are essential for locking and unlocking your door. The plates made of metal are located between the top and bottom jambs of the door which are where they help support the latch. The door latch slides into this strike plate and creates the seal. If the strike plate is damaged, rusted, or not properly installed, it could stop the latch from locking the door securely.

A misalignment of the strike plate and latch is the most common reason for the patio lock not to close or stay. This can be checked with the "lipstick" test. Apply some lipstick along the edge of the deadbolt and then cover it with masking tape. When you shut the door, the lipstick will leave marks on the tape that will show exactly where the latch meets the strike plate. If the mark is too low or high you can alter the strike plate.

The sliding patio door locks protect your home from intruders, and if they're not working correctly, you should solve the issue fast. Follow these easy steps to repair your patio door lock and restore its function.