알마즌닷컴

Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to auto locksmiths with experience who have the appropriate tools and know-how. They can create and program new keys much quicker than a dealership and at a lesser cost.

A dead battery for your coin is most likely to blame if your key fob stops locking or unlocking the doors. There are many other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking, and will not start the engine. In this situation you'll need to choose the alternate method to start as described in your vehicle's owner's manual.

Another reason why the 208 won't start is because the spark plugs are worn down. The spark plugs are responsible for igniting the fuel which starts the engine. However they are limited in their time of life. They'll eventually degrade when they aren't used enough.

Luckily, there's an easy solution to this problem. Check the voltage of the battery using a multimeter. If the voltage falls below 11,5 volts, it's time to replace it. If the battery has corroded, it is important to clean its contacts. You can do this by lifting the rubber covers that cover the two battery terminals and using wire brushes to clean any parts that are corroded from the battery. Then, reconnect the positive pole cables to the negative.

Water Damage

If your 208 won't turn on and the battery isn't flat then you should check that the spark plugs are working. You might find that they are simply too filthy and don't spark. The spark plugs can be cleaned in a workshop.

Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the proper signal to the vehicle.

This is a frequent issue that can be caused by water damage. This is a common issue in more cold climates where the car has been exposed to snow or rain. In this instance, you should contact a trusted locksmith who will have the tools and equipment required to change the key's programming. They will also have the most up-to-date technology and the machinery needed to create the Peugeot 208 smart key. The process shouldn't take longer than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips with a new model that utilizes electronic components that are mounted on a circuit board. The new system is great when it's brand new, but the circuit boards begin to degrade with time and cease to function properly.

This could stop the immobiliser's function from being activated, meaning the vehicle won't start. Contact a Peugeot specialist or a locksmith, if this is the case.

A common problem is when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery and then cut a new key blade for you. This is a quick fix.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the ground, being exposed to a sudden rain or accidently washing it, it could be due a malfunctioning receiver module. The receiver is responsible for transmitting radio frequency signals to an on-board computer that controls the central locking system within your peugeot 206 key replacement vehicle.

Rubber seals on the key fob prevent water from getting to the electronic chip. However prolonged exposure to water can break through these seals, causing damage to the chip. The high salt content of the pool or ocean water can cause damage to the key fob, especially if it is submerged.

The module must be replaced if the Peugeot spare key isn't working anymore. This can only by done by a Peugeot specialist or an expert auto locksmith. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the correct codes to start the car. This is why you should only trust an experienced Peugeot locksmith for the job of designing and programming a replacement.

Faulty on-Board computer

The on-board computer inside your Peugeot is responsible for a variety of the systems in the car, from power windows to airbags. If something goes wrong with these systems, they will usually show a code that identifies the issue. The code is stored within the system until the issue is fixed. This can often mean that the on-board computers to be replaced.

The most typical reason for the warning light of the airbag to turn on is corrosion or loose connections in the sensor. This could be due to wear and tear, ageing, or exposure to moisture and salt. It is imperative to have this issue resolved as soon as possible, since a malfunctioning airbag can be dangerous in the event of an accident.

If your Peugeot is showing a card that is not being detected error, the battery in the key fob might be dead or weak. This will stop the key fob from sending a signal to disable the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If this does not work, the key battery must be replaced.